Before doing so, make sure to unplug the wires to the motor, turning the power off while you work. To get to the gearbox, you'll need to remove the motor which is a fairly simple process. If it doesn't, it's time to buy a new one. Before replacing the motor, use a multimeter to check the voltage. If it still isn't working, you may have an issue with the gears or the motor linkage. Is your step motor making a sound when you try to retract or extend the steps? If so, it is time to check underneath for dirt and debris that may be clogging the motor or wires.īlow it out and clean it, then try the steps again. To check this, you will need to connect a voltmeter to the battery. According to Lippert Components, the battery should have a voltage of about 12.6 volts. The next step is to test it to see if it has power. Look underneath the steps to find the battery. Turn off the ignition to see if this is the culprit. However, if the RV is running, the steps will remain retracted for safety purposes. Locate the override button, and make sure it is in the "auto" position. This will allow them to remain extended while you are parked instead of retracting when the door is closed. Many RVs have an override feature for the steps. You can find replacement magnetic switches on Amazon. Make sure to perfectly align the magnet on the door and the switch on the door frame. It is best to put it in the same place as the old magnet however, you can place it anywhere that is more than six inches from the bottom of the door to the bottom of the magnet. The magnet must be placed vertically, or it will not function. Once you have finished the wiring, peel the adhesive from the backs of the new magnet and switch, placing them properly inside the door frame and on the edge of the door. Using the wire crimper, secure it into place. Use wire crimpers to secure the butt connector into place.įor the ground wires, you'll strip the casing back on the shorter wire, folding it until it fits into the ring terminal. You'll need to cut the brown wire, stripping it back roughly half an inch before attaching a heat-shrinking butt connector. Now it's time to run the existing wires through the hole in the door frame. Disconnect both the ground wire and the one connected to the box.įollow the wires to the underside of the RV. If you have no knowledge or prior experience with connecting wires, you may need a little help with this next step. Then, you'll do the same with the magnet in the door frame. Using a screwdriver or drill, you will first remove the magnet from the door. Therefore, you will need to keep the old screws and hardware for use with the new set. Removing the SwitchĪccording to Lippert Components, new switch kits do not come with hardware such as screws. If this doesn't work, it's probably time to replace the switch. This typically only requires you to tighten them back into place using a screwdriver or drill. If the two are misaligned, reposition them. Part of it should be situated on the door, while the other piece should be inside the door frame. To fix this, open the RV door, and locate the magnetic switch. Therefore, if the switch and the door are not properly aligned, your steps will begin to act irregularly.
When the door aligns with it, the steps retract. The magnetic switch is located inside the door frame. If this switch malfunctions, your steps will not work properly. If you have automatic steps, your RV contains a magnetic switch that tells the motor each time the door opens or closes. Likewise, the steps retract when you crank the ignition to keep you from driving away with the steps down. Manual steps, on the other hand, have a switch that you must press to either lower the steps or retract them. Automatic electric steps let out each time the door opens and pull back in when the door closes.
#AMP STEPS MOTOR MANUAL#
They either have manual steps or automatic. RVs have one of two types of electric steps. Why are My RV Electric Steps not Working? If you purchase something through a link on this page, we may get a commission, so thank you!
#AMP STEPS MOTOR HOW TO#
You'll also discover where to find the step motor, how to lubricate your RV electric steps, how to remove the motor, and much more.īefore you continue reading, let us say we hope you find the links here useful. Now that you know some of the possible causes for your RV electric steps not working, keep reading to learn how to fix those issues. The most plausible causes of electric RV steps not working are the following: We set out to help you understand the possible reasons for malfunctioning RV electric steps and how to fix them. Steps that are stuck in the down position make driving dangerous, and steps that won't let out cause the risk of falling. If your electric RV steps stop working, you can have bigger problems on your hands than just convenience.
0 kommentar(er)
